Vertical Mirrors 

Made using Pre-Preg Carbon. Super light at only 0.35kg per Pair! Aero design for minmum drag. Supplied with all fixings.

Horizontal Mirrors

Made using Pre-Preg Carbon. Super light at only 0.35kg per Pair! Aero design for minmum drag. Supplied with all fixings, minutes to fit.

Internal mirror mounting covers   

Pre-Preg Carbon construction, made to cover the mounting screws inside the door. A neat solution meaning you don't have to remove the door card to remove or reaplce the mirrors.

SatNav Carbon blanking panel

Pre-Preg Carbon panel to cover the SatNav area.

MOTEC Dash mount

Dashboard mount for MOTEC dash. Fits over the existing satnav area with sun hood to avoid glare.

Coralba mount

Made to fit on the right hand side of the dashboard for LHD cars. Made using light weight Pre-Preg carbon.

Centre console cover with switch mounting

Very light weight cover for the centre console. Made with a switch mounting area over storage arear under heater controls. Not just a cosmetic cover.

Co-Drivers Footrest

Made using Pre-Preg carbon with thicker areas for stiffness. Conforms to the lastest FIA regs. Available in LHD 

Drivers Footrest

Made using Pre-Preg carbon for a very lightweight product. Available in LHD

Premium Window Vents

Pre-Preg construction using high quality filter foam sandwiched between moulded carbon. A premium looking window vent.

Club Window Vents

Made using 1 sheet of Pre-Preg Carbon with a layer of high quality filter foam on the inside. Afixes with a strong carbon channel for durability against the window edge.

Front Door Cards

Pre-Preg carbon door cards. Made to be able to accept the OEM door handle as well as the window switches.

Rear Door Cards

Pre-Preg carbon door cards. Made to be able to accept the OEM door handle as well as the window switches.

ATL Fuel Pump Cover

Pre-Preg Carbon cover for the fuel pumps when using an ATL bag tank. Easy access removable cover for Fuel pump maintnance. Available only through our partners at ATL. Please see link below for contact details.

PIAA Lamp Pod

Pre-Preg Carbon or GRP lamp pod. Made to accept 180mm PIAA lamps. Ballast mounts included as well as all fixings requied. Designed to fit very low out of the airflow to maximise top end speed while also allowing air into the grill. Can also be supplied complete with HID or Halogen lamps.

IPF Lamp Pod

Pre-Preg Carbon or GRP lamp pod. Made to accept 110mm IPF lamps. Ballast mounts included as well as all fixings requied. Designed to fit very low out of the airflow to maximise top end speed while also allowing air into the grill. Can also be supplied complete with HID or Halogen lamps.

Standard Fuel Tank Guard

Standard fuel tank guard. Twintex construction for a good ballance between weight and durability.

ATL Fuel Tank Cover

Pre-Preg Carbon/Kevlar construction due to proximity to exhaust system. Available only through our partners at ATL. Please see link below for contact details.

Diff Pump Guard

Light weight Twintex construction. Enclosing the diff pump protecting from foreign debris. Fixes to the existing mountings for easy fast fitting.

Floor Guards

Rear Arch Protector

Rear arch protector made using Twintex. Made to cover the leading edge of the bumper to protect this area. Also made with a flat edge to enable secure fitment of a mud flap.

Front Wheel Arch Guards

Twintex arch guards made using flat sheets of Twintex cut to shape with airflow holes and mesh to allow airflow to coolers.

Front Sill Guard

Twintex sill guard, maximum strength with thicker areas in areas of high erosion.

Rear Sill Guard

Separate rear sill guard made using Twintex for maxiumum protection as well as maximum cost saving as this can be replaced without having to replace the entire sill guard.